Smith And Wesson 32 Long Serial Number Lookup

Partnership with Horace Smith & Daniel B. Wesson was from 1856–1874. Family owned by the Wesson Family from 1874–1965. Smith & Wesson became a subsidiary of Bangor-Punta from 1965–1983. Between 1983–1987, Smith & Wesson was owned by the Lear Siegler Co. On May 22, 1987, it was sold to R.L.Tomkins, a British holding company. I have a revolver that I do not know a whole lot about. It has been determined to be a smith and wesson hand ejector made some time in the 1950s. I have noticed that there are two possible serial numbers, there is one on the yoke and one on the butt of the gun. Locate the serial number on the left side of the pistol's frame. The standard location for the serial number is above the trigger guard. Some serial numbers are located underneath the frame in.

S&W.32 Long Hand Ejector Mark, The 'Standard Catalog of Smith&Wesson' lists your revolver as a.32 Hand Ejector, Third Model. With serial number 326575 on the butt it fall within being made from 1911-1942. Built on the round butt I frame with five screws. Yours should have a heat-treated cylinder. Hope this helps. The Second Model.32 Hand Ejector Fifth Change was made from 1910 to 1917, with serial numbers that begin at 102,501 and run to approximately 263,000. Please write to me if you have a serial number in this range and can help make this last figure more accurate. Third Model.32 Hand Ejector &. The Smith & Wesson Model 30-1. The gun is an example of the tried-and-true hand ejector design that appeared in 1896. Model 30-1 with cylinder open. Being late in the series of improved versions that have appeared since, this one has the J frame, ramp front sight on a 4-in. Barrel, flat thumb piece, diamond in the grip, and serial no. Jun 05, 2009 Identifying features: This is where to look for the model number (not used until around 1957). Sometimes the serial number is here, especially in later models. Earlier models have them here: S&W revolver names before World War II. Name Caliber Frame.22 Hand Ejector Ladysmith 22 Long M.22/32 Target 22 Long Rifle I.

  1. The Smith & Wesson Hand Ejector First Model, commonly referred to as the Triple Lock, is one of the most coveted large-frame revolvers of the 20th century. For many, this gracefully configured.
  2. Smith & Wesson.44 Hand Ejector 'Triple Lock' with blued finish, courtesy of Adams Guns. The first large framed Smith & Wesson Hand Ejector model. Now referred to as an N frame revolver, but for many decades was known as the 44 frame.

The first .38 Special revolver

Swing out cylinder, solid frame, double action revolvers were well established by the last decade of the 19th century.Iver Johnson employed the concept as early as 1879 and Colt’s Models of 1889-90, chambered for the .38 Long Colt cartridge were the standard U.S. Military sidearm by the early 1890s. Smith and Wesson called their version a “ Hand Ejector” to differentiate if from the break –top, automatic ejection arms of the time. In 1899, the Army and Navy placed orders with Smith and Wesson for two to three thousand (sources vary as to the exact number) Hand Ejector revolvers chambered for the .38 U.S. Service Cartridge (Long Colt.). It became the Military and Police model of 1899. The need for these additional revolvers arose during the Spanish- American War.These revolvers, along with the very similar Colts were in service during the Philippine insurrection of 1899. Early sources universally report that the old Long Colt cartridge was considered inadequate against the Moro warriors encountered there.Smith and Wesson responded by lengthening the .38 case and increasing the powder charge and bullet weight.Nominal velocity of the new .38 S&W Special cartridge was 870 feet per second against the reported 780 fps of the earlier round.Bullet weight increased from 150 to 158 grains and the black powder charge upped from 18 to 21 grains.It is clear that the military contract revolvers chambered the .38 Long Colt round.Early references indicate that the .38 Specials might have gone to the civilian market.Serial number run from number 1 in the K Frame Military and Police series to 20,975 spanning the years 1899- 1902.

At a glance, the model of 1899 appears nearly identical to the quintessential M&P of the 20th century.The primary visible difference is the absence of a front locking lug.The cylinder locks only at the rear and at the locking notches leaving the ejector free standing.Barrel lengths are four, five, six and six and a half inches with finish options of blue and nickel. There are also target-sighted versions. These and serial number blocks-associated with small military orders, are very desirable as collectors items.

First Model M&P revolvers often exhibit the extremes of neglect. Black powder, chlorate priming and owner indifference take their toll among many examples. They do not fare nearly as well as the hand ejectors of 1902 and later.

Smith wesson serial numbers manufacture date

Mine, number 8200, has only minor finish blemishes and is in near-new mechanical condition. The cylinder and crane lock tightly into the frame and timing is perfect. The bore and chambers are pristine and the internal lockwork - once relieved of decades of congealed lubricant - might well have been forged last week instead of 103 years ago. According to the factory letter, the revolver went to Bekeart & Company of San Francisco CA on December 20, 1900. Additional provenance shows the M&P registered to an E6 at Wheeler AFB, Hawaii in 1975 and has remained in his possession until this year.

Shooting the first .38 Special revolver

While the early Smith and Wessons resemble the Colt double actions in function and broad outline, I have always found the handling characteristics and the action of the Smiths to be much more desirable.This is purely a personal opinion and the gun magazines used to rage over the question “ Which is Better? Colt or Smith and Wesson.”M&P # 8200 with its frame fitting round butt and six- inch barrel points very well. The sight picture, comprised of a knife-sharp front blade and a tiny rear notch proved to be the limiting factor in shooting precise groups. On the other hand, the four pound single action trigger and the typically smooth Smith and Wesson Double Action, were great aides to practical accuracy.Many service revolvers and autos of the 19th and early 20th centuries feature raunchy six- pound single action triggers making it very hard to achieve any degree of precision.

M&P cylinders were not heat treated until 1920 so standard; factory level pressures are the order of the day.

My standard .38 Special load is 3.5 grains of Alliant Bullseye and the available 158- grain Lead bullet.This is a few tenths grain under the listed factory duplicate and the tightly gapped Model 1899 averaged 859 fps with the swaged Hornady SWC and 862 with a five round string of machine cast 158 SWC. This and subsequent shooting was done in five shot strings.The First M&P has no provision for a hammer block safety and while earlier owners no doubt loaded all six chambers with impunity, hindsight demands that we leave an empty under the hammer.

In keeping with shooting practices at the end of the 19th Century, I did most of my shooting one-handed.This is how Walter Mitty’s dad would have done it and it captures the flavor of the era.My 25 yard bench groups and fifty foot off hand efforts ran four inches.I was unable to fully exploit the accuracy of the revolver because of the sight picture. Point of impact was dead on for elevation and slightly to left of point of aim.

The light recoil of the standard .38 Special and the superior handling qualities of the Smith Hand Ejector came into their own in the more “practical” shooting exercises. Firing double action single-handed with the shots spaced about one second apart, I was able to keep fifteen consecutive rounds in the center ring of the Texas Police Target at twenty-five yards. The sights did not seem much of a handicap in this application. The revolver came very naturally up to point. A clear flash sight picture came about naturally and hung steady through the smooth double action pull. I also managed ten consecutive hits on the upper torso from a vertical braced position single action at fifty yards.

The Military and Police first model emerged as a dynamic reactive tool for the gunfighter of a century ago.It continues to satisfy the essential criteria for a personal sidearm in the present day.

Got something to say about this article? Want to agree (ordisagree) with it? Click the following link to go to the GUNBlast Feedback Page.

TheSmith And Wesson

Militaryand Police Hand Ejector

Smith And Wesson Hand Ejector Serial Numbers Lookup

Model of 1905, .38 Special

writtenand photographed by Mike Cumpston

editedby John Dunn

Clickany thumbnail for a larger photo.

TheM&P is frequently cited as the most prolifically manufactured handgun inhistory and it certainly did define the double action revolver during the 20thCentury. A pocket history is in order and I will dwell on certain high points ofits development rather than attempting to cover the many evolutionary changes inthe design. The history is obligatory--although off-repeated and undoubtedlyboring to those familiar with the subject.

It appears that themodern, service caliber swing-cylinder, hand-ejector revolver dates from theColt Army and Navy Models of 1889-1892 then chambered for the .38 Long ColtCartridge. The Smith and Wesson First Model Hand Ejector Military and Policecame out in 1899 and closely resembled the Colt in size and function. Like theColts, this First Smith and Wesson had a free standing ejector rod and thecylinder locked into the frame at the breach only. The .38 Long Colt Cartridgewas a step up from the very early .38 Colt which became known as the .38 ShortColt. The switch was made from a case diameter healed bullet much like that ofthe current .22 Long Rifle to a hollow based round nosed projectile of 150grains. The hope was that the bullet would slug up to fit the bore and affordsome degree of accuracy. Loaded over 18 grains of black powder, the nominalvelocity is reported in the mid to high 700 fps range. It was a cartridge thatcould be expected to lob a bullet well into and frequently, all the way througha human torso and was reported to be less intimidating than the large borerevolvers previously issued to minimally trained military and police personnel.

The .38 doubleactions saw some use in the Philippine Campaign of 1899 and afterward and therewere reports of inadequate performance on the highly motivated and reportedlydrug enhanced Moro adversary.

This is the reportedmotivating factor for the development of the .38 Special Cartridge and theimproved Hand-Ejector 2nd Model of 1902. The Special had a slightlyelongated case and a 158-grain round nosed bullet over 21 grains of blackpowder. Velocity is reported at 870 fps but it is notable that current smokelesspowder cartridges frequently show velocities in the high 700 fps range. Somesources report that examples of the First Model M&P of 1899 were chamberedfor the Special cartridge making it possible that the round actually predatesits official introduction in 1902. The hand ejector model of 1902 and itssuccessors had a front locking lug under the barrel and a number of importantaction changes took place over the next several years. The Model 1905incorporated a passive hammer block in the '4th Change'variation of 1915. Heat treating of cylinders began in 1919 and, in 1922 thefront sight and rear sight groove were widened for better visibility. From 1915through 1940 (or 1942 in some references) changes were relatively minor. Serialnumbers began with the First Model of 1899 and reached about 700,000 beforeWorld War II. Barrel length options on the basic service revolver included 2(1933), 4, 5 and six inches with the five inch length being particularlypopular.

The design underwentfurther lock-work changes directly after WWII with linear descendents of theM&P remaining in production into the 21st Century.

AK Church (http://milesfortis.com/church/akc07.htm)aptly characterized this model as being so common as to slip into the woodwork.Everybody from Bogart to Jungle Jim to Rocket Man had one and the M&P becamethe archetype handgun in the public eye for most of the last century. Itsassociation with snap-brimmed hats, flap holsters and pith helmets, not tomention police uniforms sent many a potential handgun buyer to the hardwarestore in search of 'one of those .38 Police Specials.'

My present exampleof the M&P is a Model of 1905 4th change produced in 1938 or 39equipped with a 4' barrel and the original numbered service type stocks. Itretains most of its high polished commercial finish and appears to have spentmuch of its life span holstered in a drawer. It has been fired, cycled andhandled very little and the impression is that the action is mechanically new.The single action trigger breaks at between 3.5 and 4 pounds and the cylinderreaches full lock-up well before double action release. Overall handling andshooting characteristics are very much like those of my old 1947 5' barrelM&P and a 6' Model 10 from 1958 or 59. If anything, the current exampleis less-used than the others and is a bit less smooth at the end of the doubleaction cycle. There is no evidence that anyone has removed the side-plate andtampered with the action. Upon first inspection, I primed several cases with CCImagnum pistol primers and tried the double action. One primer of six detonatedgiving rise to the possibility that (1) somebody had shortened the mainspringstrain screw or, more likely (2) like many old and modern double actionrevolvers, it was never designed to function against the unreasonably tough CCIprimer cups. I wondered if possibly the leaf mainspring might have lost some ofits strength during the past 64 years. This idea was shot down by premierpistolsmith, Alex Hamilton who said 'your mainspring will last forever…'

I found a spentlarge pistol primer with the anvil gone and capped the strain screw. Theadditional purchase proved a positive fix.

Smith And Wesson 32 Hand Ejector Serial Numbers

Shooting It

There is now abewildering array of .38 Special load variations. The standard loading in thefirst half of the 20th The belko experiment online, free. Century was a smokeless powder loading of the158 grain lead round nose. There was a 'Super Police' loading of around nosed 200-grain bullet, a metal capped RN and the 148-grain wadcuttertarget load. The 'High Speed' or 38-44 loads as well as the sharppointed jacketed 150grain metal piercing load were recommended for the largerframe heavy duty revolvers. It is widely held that the M&P revolvers thatpredate the Model 10 of the late 1950s are happier off with the standardpressure load not exceeding 15,000 pounds per square inch. Notably, by 1959Speer was testing 18,000 PSI loads in K-frame revolvers and I used a bunch ofthese loads in my old early post-war model. This was an accepted practice at thetime but not one I care to repeat or recommend with my vintage 1905 4thChange. Accordingly, I concocted several loads matching nominal factoryperformance.

Load

Velocity /Energy

Ex Spread 5 rnds

Groups 25 Yards

2.7 Bullseye 148 wc

676 150

51

2'

158 c/swc 3.5 Bullseye

755 200

52

4'

158c/swc 3.5 700x

855 257

43

4'

158 Hornady 4.3 Unique

751 197

68

2'

The cast semi-wadcutterover 3.5 Bullseye and the swaged Hornady SWC over 4.3 Unique closely duplicateactual velocities I have gotten with modern factory round nose loading. The 700Xload approaches the published velocity of the same factory loads. The 2.7Bullseye /cast wadcutter load is a traditional bulls eye shooter's standard withmany target shooters upping the charge a bit for the 50 yard segment of the NRAbulls eye matches. These loads will do everything I expect of the vintageK-frame revolver. The present example preferred the wadcutter and swaged Hornadybullet loads over the cast SWCs, turning in two-inch 25-yard groups from mybench set-up.

………And a 2' Smith and Wesson Bodyguard

While putting together material on the M&P, I became temporary custodian of a Smith Airweight BodyGuard. This is the version of the J-Frame Chief’s Special with the hammer shrouded but not completely enclosed as on the Centennial Model. This is aluminum –frame 14.5 oz five shooter designed for pocket or hand warmer carry. Because of the small size and light weight, it was often recommended as a woman’s gun- the recommendation reflecting a certain lack of clarity in regard to female shooters and the shooting characteristics of extremely light-weight firearms.

The present example showed signs of having been fired on three chambers only with two of the chamber faces showing no indication of powder burn or any application of cleaning abrasive on the nickel plate. It develops that the factory assembler had neglected to set the handspring and the cylinder did advance at all when the trigger was cycled. I set this right and found that the BG had a nice smooth, double action. Having significant experience with a couple of varieties of Chief’s Special and no memory of ever firing a body guard or yet an alloy frame snub, I was definitely interested. I proceeded to remedy this with fifty rounds of the 4.3 Unique/ 158 load. As a matter of interest, my records show velocities from two inch snubs with 158 grain factory round nose to range from the low to mid 600 feet per second. The 200 grain Super Police rounds recorded 580 fps in a Chief’s Special. These heavier bullets were sometimes chosen because, while they travel point forward in flight, they began to yaw and tumble upon impact –possibly causing a larger crush cavity. Smith and Wesson was emphatic and consistent in warning against any use of +P ammunition in the alloy guns.

Recoil with the factory approximate rounds was jarring enough to take it out of the learner’s gun category and, by the end of fifty rounds; I had had about as much fun as I could stand. Nevertheless, range performance was gratifying. I began at three and five yards drawing from my duster pocket and firing single-handed point shoulder at the TXTP target and the moved to seven and ten yards where I went to a two handed hold and sighted double action fire. At these short ranges, the quick doubles all landed in an A-Zone spread.

Continuing double action at 15 yards, I widened the group just a bit but continued with solid center mass hits. At 25 yards, I put four out of ten rounds a couple of inches below the center five ring but the hits were still well centered with the other six rounds joining the earlier short range cluster.

While I didn’t do any single action shooting with this revolver, I noticed that the hammer spur is just as accessible as that of the fully exposed Chief’s Special. This is a positive point as I have found that torso hits can be had with the two inch revolvers all the way back to fifty yards when the shooter drops to prone and uses the single action option.

Designed to be carried much-shot little, the BodyGuard and other snubs are capable of effective accuracy well beyond the usual range for defensive shooting. At closer ranges, great speed and tightly centered multiple hits are available to the reasonably experienced shooter.

This appears to beabout the best accuracy I can produce with the 4' revolver--which is tosay, not quite up to the full potential of the gun-loads. During bench shooting,I saw that the gun was printing several inches low at

25 yards. The same wastrue of my earlier five and six inch models. It becomes necessary to cover thedesired point of impact with the sight picture during practical shooting andmakes the revolver suitable for small game hunting at close range only. It alsothrows an important crimp into enjoyable precision bulls eye shooting at theusual distances.

Said limitationsbeing what they are, I set out to explore what of a practical and enjoyablenature might be gleaned from the M&P. When my Model 1905 4thChange came out of the factory at the tail end of the Great Depression, whatformal handgun training that existed leaned heavily toward the techniques ofbulls eye shooting. The gun was extended from a single hand and fired singleaction to take advantage of the light and short trigger pull. In contrast tocurrent practical training the targets were placed at great distance – 20 to25 yards at the shortest and consisted of a primary aiming point somewhatsmaller than the common tea saucer. The cursory nature of most handgun trainingprograms combined with the approximate nature of fixed sight regulation and suchmatters as the expense of ammunition gave rise to such cultural truisms as, 'Can’tnobody hit nothin’ with no pistol! Pistols is inaccrit!'

While few peopleapproached anything like proficiency with the short gun, an enthusiast with amodicum of practice could give the lie to the generally held perspective. Thiswould be particularly true if the bygone shooter was equipped with an M&P.The single action break of under 4 pounds coupled with a double action pull inthe 11 to 12 pound range compares favorably with most service actions of historywhich, more often than not, exhibited single action trigger pulls of six poundsand more and double actions-where present- in the 15-17 pound range.

After using up oneof the TXTP silhouette targets in general familiarization, I set one at 25 yardsand began to shoot 'for the record.' That the historic lack of respectfor the double-action firing mode persisted into the late 1930s was evident inthat the hump-backed hammer at rest obscured much of the rear sight notch. Thishold-over from the double actions of the 19th Century made itnecessary to refine the sight picture after initiation of the DA stroke. Thisproved no real impediment to effective one-handed double action shooting at 25yards. The rounds, launched with a straight--through pull impacted, with oneexception, in the high scoring five ring of the target. I made an earlycorrection to move the group upward and to the right, but even so, the majorityof the shots would have A-Zoned one of the IPSC targets. The overall geometry ofthe revolver and notably a favorable trigger reach contributed to shot breaks abit over the one-second mark. Recoil with the frame-fitting service stocks madeitself known on my thumb joint but did not approach the painful over the courseof several extended shooting sessions. Two-handed twenty-five yard double actionshooting narrowed group size but perhaps not to the degree that might beexpected. In the course of any practice session, I like to do a bit of off-handsingle action shooting trying for precise placement at 25 yards or thereabout. Icombine this with some work on the head segment of the targets when shootingsilhouettes. One- or two-handed single action shooting lands almost all shotssome where in the head or neck region.

In the earlyshooting session, I moved the Silhouette back to fifty yards and fired twelverounds one-handed single action using the head as an aiming point. Eleven of thetwelve rounds impacted the 5 zone while one round landed about 4' outsidethe silhouette and over the left shoulder. The Hand Ejector Military and PoliceModel of 1905 4th Change accomplished the above described process ina confidence building and satisfactory manner. Group sizes are somewhat largerthan I have come to expect firing the same drill with an accurate 1911 .45 or aheavier Smith or Ruger revolver. On the plus side, the overall ergonomics of therevolver provide a speed advantage over the larger cylinder guns and just aboutequals that of the self-loader. This is not a shabby testament to a compactsidearm that, at 30oz or a bit less, is eleven or twelve ounces lighter than therevolvers I wear about on a daily basis.

The M&P is noless well suited to the more modern shooting modes. Drawing from strong sideconcealment, I fired a series of doubles from three and seven yards. Initialshots were in the 1.5 to less than 2 second range while I guess my shotintervals to be in the .20 to .30 second range. Precisely aimed double actionshots into the head from seven yards produced a nasty twelve round ulcer thatstood testament to the surgical capabilities of the old handgun.

A sixty (or eveneighty) year old hand-ejector revolver gives up very little in comparison withthe revolvers of the present time. My example retailed for $33 in the 1940Stoeger Catalog, which translates to $426.86 in Y2K fiat dollars. This iscomparable to current prices of the M&P progeny representing a pretty goodweeks’ salary then and now. Mine proves a particular bargain at $250. This isright in line with the current Blue Book estimate--no ad valorum tacked on forsuch intangibles as the commercial carbona blue finish, the forged lockwork, thehand polishing and the finely checkered figured walnut grips. A modernnostalgia-piece knock-off of the M&P recently went out of the SmithPerformance Center to one of the major distributors. It attempted to recreatethe flavor of the old M&P using modern technology with the added flourish ofa color case-hardened frame in the same style as the more recent HeritageSeries. The retail bite of $700 to $1,000 is motivation enough for the modernshopper to direct a bit more attention to the old Hand-Ejectors than hashere-to-fore been the case.

Further Notes onthe .38 Special Cartridge:

With some regularityit is demonstrated that a person shot with a given firearm will not react in theexpected manner. The standard operating procedure is to fall down and quitwhatever you were doing immediately prior to being shot. When this does nothappen, there is much consternation and all the wrappings and trappings of'cognitive dissonance' come into play. The ubiquitous nature of the.38 Special has allowed it to fail (and succeed) in its assigned role perhapsmore than any other round in history. Never mind that everything from the .22Short through the .44 Magnum demonstrate failures to stop on reasonably frequentoccasions, the .38, by virtue of its universal distribution quickly developed areputation as a poor stopper. That it also developed a reputation as a goodstopper is beside the point.

Recently, I read astory about an early 20th century lawman who entered a bar and shotdown five or six gentleman killing them outright and immediately with his model1902 M&P Second Model loaded with black powder round nosed CTGs. ColonelCharles Askins described killing two men with the .38 RN load and was quitedelighted with the results. More recently, Bernard Goetz plugged four gang-bangerson a New York train and every one of them lived to admit that they had beenplanning to jack him with their sharpened screwdrivers and did not do so onlybecause they were shot. The civil rights of the disadvantaged youths werevindicated when a New York jury convicted Goetz of feloniously shooting themwith an illegally carried firearm. Many things have been written on the subjectof stopping power as it applies to the traditional .38 Special load and many ofthem are not true. Likewise many of them are true and it becomes a thankless,life-long task figuring out which is which. Meanwhile, the reader is requestedto develop his own personal theory of stopping power and his own take on theutility of the .38 Special.

The 1905 M&P 4thChange was produced in huge and bewildering numbers. Assistance in dating thisexample was provided by:

bruce hmx
wheelgunner 610

Smith And Wesson 32 Long Serial Number Lookup Us

rburg
smithnut

Of http://www.smith-wessonforum.com

Who pulled out theirreference books, personal revolvers and factory provenance letters to narrow theproduction period of number 667,XXX to 1938-39.

Thanks is also dueto AK Church (not his real name) who wrote the reference piece located at:

http://www.milesfortis.com/church/akc07.htm

His shootingimpressions of the M&P and Model 10 were much appreciated.

As usual the smartwork and editorial oversight is provided by Mr. John Dunn, the Lone Gunman whooccupies the Chair of the Creative Cybercide Foundation also located at thisaddress.

Mr. Miles Fortishimself provides the bandwidth and willingness to host and publish this andother ramblings of your humble correspondent and his indulgence is appreciated.

Smith & Wesson Serial Number Chart

Historicalreferences are drawn, in part from W.H.B. Smith’s Book of Pistols andRevolvers and; Sixguns by Elmer Keith. Other sources, as well, contribute to thehistorical data and it may be important to note that none of them are in perfectagreement.

S&w Hand Ejector Parts

Smith And Wesson 32 Hand Ejector Serial Numbers

since the website crashed AUG 2003

This post describes the design and performance of a fine Smith & Wesson .32 revolver.

I have been a .32 fan since dad showed me Great Grandma’s old Harrington and Richardson. She carried it in her apron pocket during the Great Depression when hobos would stop for a handout at her house. The Smith & Wesson Model 30-1 considered here never saw such menial duty. The blue box is worn and the gun has a light cylinder ring but was unfired when purchased. It came from the collection of a fellow who bought and squirreled away some guns in the mid-twentieth century. When he passed recenty, his family found and consigned them for sale. Lucky for me I connected with this beautifully finished little revolver before someone else did.

The Smith & Wesson Model 30-1

The gun is an example of the tried-and-true hand ejector design that appeared in 1896.

Model 30-1 with cylinder open

Being late in the series of improved versions that have appeared since, this one has the J frame, ramp front sight on a 4-in. barrel, flat thumb piece, diamond in the grip, and serial no. 725XXX that means production in 1963. I like the looks of the long, serrated front sight and the round grips. This syle of grip seems appropriate on a gun of this size. Although it is small for my average male hand, it is still comfortable. The great workmanship and appearance of the gun shows why I like Smith & Wessons. They are among the finest of affordable mechanical devices.

Smith And Wesson 32 Long Serial Number Lookup Model

This gun has been patiently awaiting its destiny in its box for fifty years. Turns out its destiny is to be shot by me and I am going to shoot the heck out of it. Its strength and quality will surely mean it can take it.

Shooting the Model 30-1

There are four bullet designs in the factory ammo that I had on hand for this test: Several different brands have the standard round nose, one has a half-jacketed hollow point, one has a flat nose that is like an old version called the .32 Colt New Police, and a couple of others have target wadcutter bullets. The picture shows, left to right, an Aguila 98 gr RN, a MagTech 98 gr half-jacket hollow point, a Sellier and Bellot 100 gr flat nose, and a Fiocchi 100 gr wadcutter.

Here are the velocity results for these loads (Ave = average velocity, 10 rounds, ES = extreme spread,and SD = the standard deviation):

Winchester 98 gr Round Nose Ave 665 fps ES 108 fps SD 34 fps

MAGTECH 98 gr Round Nose Ave 620 fps ES 79 fps SD 30 fps

PRVI Partizan 98 gr Round Nose Ave 542 fps ES 112 fps SD 37 fps

Sellier and Bellot 100 gr Flat Nose Ave 696 fps ES 107 fps SD 31 fps

Aguila 98 gr Round Nose Ave 624 fps ES 52 fps SD 14 fps

MAGTECH 98 gr Jacketed HP Ave 483 fps ES 154 fps SD 43 fps

Fiocchi 100 gr Wadcutter Ave 616 fps ES 101 fps SD 30 fps

Federal 98 gr Wadcutter Ave 734 fps ES 74 FPS SD 28 fps

I found that fired cases came out very dirty, because the cases obturate (seal) poorly at these low pressures. Extreme spreads were large, exceeding 100 fps for more than half the brands; Standard deviations were correspondingly large, 30 fps or more for three fourths of the brands. Considering an SD of 30, and knowing this means that 95% of shots will fall within a range of plus or minus two standard deviations, I see that it takes a range of 120 fps to catch 95% of my shots. That is a wide range when the average velocity is only in the 600s.

The Federal wadcutter load won the velocity race, and it would be the best factory choice

Load at this end!

for small game or self defense. It is also the most expensive load. I liked the Sellier and Bellot a lot. It gave good velocity and the flat-nosed bullet would be more effective on small game than the round noses. The Aguila had the best uniformity. The MagTech jacketed round was worthless.

Overall accuracy of the loads was good to very good. I used an NRA 25-ft slow fire target and a sandbag rest when putting 10 rounds of each brand over my chronograph. Ten-shot groups ranged from 1-1/4” to 2-1/8”. The Sellier and Bellot, the Fiocchi wadcutter and the Federal wadcutter all managed groups of 1-1/4”. The Aguila was close at 1-5/16”. My eyesight is a limiting factor in group shooting, so I think these could be tightened up a bit.

Smith And Wesson 32 Long Ctg Serial Number Lookup

I found that there were a couple things I could do to get better zing from some factory loads. When I noticed that the Winchester round nose loads did not have much, if any, crimp, I got my 32 seating die out and set the bullet in several of them 0.06” lower and then roll-crimped them over the shoulder. Average velocity jumped to 730 fps (from 665 fps), with an ES of 35 fps and an SD of 12 fps. This was a considerable improvement in velocity and uniformity. These data were taken on a different day than the first Winchester numbers, but, no reason to doubt the chronograph on either day.

The second thing I found is that temperature really matters. The Sellier and Bellot ammo, after sitting in a cardboard box in the sun on the range bench, and feeling decidedly warm to the touch, gave an average velocity of 743 fps (from 696 fps) with an ES of 46 fps and an SD of 13 fps. I am not recommending this practice. The results are reported for your information.

Smith And Wesson 32 Long Serial Number Lookup For Guns

It is a joy to use a gun as finely wrought as this little, mid-20th-century Smith and Wesson. Function was perfect and smooth, and I am quite satisfied with the accuracy.

Smith And Wesson 22/32 Serial Number Lookup

I will need to make some handloads to get the best out of this Model 30-1 and that is where I am headed next. Handloading the .32 Long for good performance is easy for an experienced loader. The small case capacity makes it possible to get 2000 good loads from a pound of powder and cast bullets work very well.